High Performance The series of Har-880 TAB-RT plastic slat top chains for Brisbane Factory

Pitch:38.1(mm)

Shaft diameter:7.6(mm)

Thickness:20(mm)

Working load:2000(N)

Har-879/880, Har-880 M, Har-879/880 TAB and Har-880 TA belongs to the turn top chain. All of them can achieve change the orientation in the process of operation. The biggest character about Har 880 TABS is that it can antic-static and It belongs to straight plate chain Har 880STAB and Har-880 TAB-RT also belong to the straight plate chain. Generally ,The material about the series of 879/880 plastic slat top chain are POM. Besides, the products also can easily installation and maintenance and they have high mechanical strength. In addition, our products are widely used in food, beverage, pet bottles and aluminum cans as well as all kinds of containers transport. The detailed size can be available as your requirement, thus as long as you give me the drawing or detailed specification, everything is okay. So All-Ka has the products to suit any customer requirement.

In this video, as a part of my series of videos on advanced knife sharpening techniques I begin by demonstrating some details of of a second belt grinder that I have assembled. I then use the grinder to demonstrate a few specific sharpening techniques.

The Grinder is a 2×72″ Coote Belt grinder – https://www.cootebeltgrinder.com/ It doesn’t come with a motor. I’m using a 2″ pulley wheel on a 1″ motor shaft and a 4″ diameter wheel on the shaft of the grinder which turns the 10″ contact wheel, I am using a 3 HP motor with a peak RPM of 1800.

The motor and drive came from https://www.electricmotorwholesale.com/ Contact is Ed Frye – a superb person to work with. I didn’t correctly state the company name in the video. If you are going to do a project like this – he’s your man. Tell him Ken sent you.
302-653-1844 ext 11.

The drive came from KB Electronics. The motor is a Leeson. Again contact Ed for details. For details about how I programmed the drive, contact me.

The footswitch was obtained from Linemaster 860-974-1000 Ask for Bruce or Lee.

I rewired the switch for this application and provided Ed Frye with details.

Pulleys were obtained locally. The fanbelt was obtained from an auto parts store

The VFD or variable frequency drive is used to control the motor. Both the motor and the VFD are completely enclosed to avoid failure from dust – a necessity. The motor uses 3 phase 240 volt current. The input line voltage is a 30 amp line of 240 volt single phase current. The VFD converts single phase to three phase current and controls the motor by adjusting frequency. There are specific motor requirements for this eg the motor must be inverter ready, etc.

The footswitch takes over control of the VFD to run the motor in the forward or reverse direction and must be programmed and wired for this task. Programming can control a large number of parameters (almost 100 parameters with multiple possible values). The potentiometer (knob) on the VFD varies the speed which is displayed on the control panel, which can be set to display either RPM or frequency or arbitrary units. Using this potentiometer to control speed is one of several possible approaches that I chose from for my needs.

The footswitch is connected to the ioda (input/output) board which, among other things provides isolated control circuits for the VFD. These can be programmed (details available but beyond the scope of this video) as switches, analog and digital inputs, etc etc). I needed to rewire the original footswitch pair for my needs for this project – purchased separately. I show the ioda board and wiring hookup in the video.

Next I demonstrate speed and torque available from the setup, showing the extremely slow speed and the unit at full power. One of the most impressive things about this setup is the ability to produce LOADS of torque at low speed. Precise speed monitoring is a big plus and the ability to go in both directions is a major advantage, especially for leather belts and (in the future) nanocloth belts.

ON TO TECHNIQUE!

So I demonstrate sharpening / polishing a single bevel knife – a Nubatama White steel Deba using the flat platen and hands free on / off capability to enable precise sharpening so that the shinogi line is not adversely affected.

Next I demonstrate an advanced – and somewhat dangerous technique – thinning a knife and differentially not wearing off the labeling on a knife. Do this at your own risk. For this I use a Richmonf Artifex using M390 steel. https://www.chefknivestogo.com/riar21gym3.html This is one of the highest quality stainless type steels available. The particular belt being used is an A3 belt structured AlOX abrasive at 4000 grit.

Finally, I show how to selectively grind a specific area of a knife using a custom knife made by Farid, an outstanding knifemaker specializing in highly abrasion resistant steels. In this case it is a knife made using CPM Rex 121. I have put a convex grind on the knife using diamond belts. There is no distinct bevel on the blade – the two sides simply meet, giving a maximally acute angle for the edge – which this knife handles quite nicely.